 |
||
| GLTS is a division of Miller Machine & Grinding Service, Inc | ||
  |
PULLERS
Prices are in US dollars (prices efective
Nov. 8, 2012)
We
accept Purchase Orders
from established firms. .
 |
T-1 Counter shaft bearing puller, 100mm OD | $73.00
|
| Counter shaft bearing puller; main box; RT-RTO models: 6,7, & 9 series (front bearing position only). Removes bearings #81022, 20089, 19551 & 4303031 | K
|
|
 |
T- 2 Counter shaft bearing puller, 83mm OD |
$68.00
|
| Use for removing bearing #BS226539 and # 4302240 (FR-FRO ) from main case and off the end of shaft at same time. Also main case rear bearing position in RT-RTO 9 series ( bearing # 4302712). You will need to borrow a snap ring from a FR-FRO bearing. |
K |
|
 |
T- 3 Input shaft bearing puller, 110mm OD | $88.00
|
| Input
shaft bearing puller; all models. Can also be used on older pre-tapered
bearing auxiliaries; bearing numbers: 81008, 81052, 51557, if a
tube or pipe 8.5 inches long is used to take up space between end
of counter shaft and cross-block; see application photo. |
K CLICK HERE FOR APPLICATION |
|
 |
T- 8 Counter Shaft Pusher |
$42.00
|
|
Use to push counter shaft to expose snap ring in order to install T-1, T-2, or T-100 bearing puller. Works on all series as it uses two of the clutch housing bolt holes. |
K
|
|
 |
T-100 Reversible Bearing Puller |
|
| No longer in production. For RT/RTO - front box, counter shaft front (100 mm) bearings (81022, 20089, 19551; all RT series 5, 6, 7 & 9.) see T-1. For auxiliary counter shaft rear (110 mm) bearings (81008, 81052, 81557; used in 5, early 6, 6600, and 613 series) i.e. older ball bearing auxiliaries, see T-3 application photo using the spacer tube/bar. THERE WAS NEVER ANY FRO APPLICATION for this tool see T-2 for FRO. |
|
|
 |
T-150 Impact Puller |
$23.50
|
| Slide hammer is threaded into reverse idler shaft for removal; 1/2"-13 threads. Also pull various bearing from blind holes with the following appropriate adaptors. |
K
|
|
 |
T-151 Metric Thread Adaptor |
$14.50
|
| M12 x 1.75mm adaptor for FRO models. | ||
 |
T-155 Bearing Puller Adaptor |
$18.00
|
| Raps out #8879 and #20015 bearings on post-1969 models auxiliary counter shaft front bearings.5 and early 6 series. |
|
|
 |
T-157 Tapered Bearing Race Adaptor |
$18.00
|
| Use to remove tapered bearing race in auxiliaries which have tapered roller bearings. Helical 7 and 9 series, Super 10 and later 6 series, and all FRO. |
K |
|
 |
T-160 Bearing Puller Adaptor |
$18.00 |
| Pulls bearing # 16780; pre-1970 model auxiliary counter shaft front bearings. | ||
 |
T- 200 Bearing Puller |
|
| Auxiliary counter shaft rear (110 mm) ball bearing (81008, 81052, 81557; 5, early 6, 6600 and 613 series). This puller no longer available. See T-3 application using a spacer bar larger than 1.25" but less than 1.968" (50mm) in diameter. A piece of 1.5" (ID) pipe works well. | No longer available |
|
| T- 205 Quill Puller |
$92.00 |
|
 |
Will remove bent or broken quills from the tail shaft of 3 speed auxiliary sections in Fuller 8LL, 13, and 15 speeds. Saves the price of a new quill assembly! More than pays for itself the first time! |
CLICK HERE FOR APPLICATION |